Abstract:
This paper presents the architectural lay-out and functional design details of a microcontroller embedded electronic monitoring system (e-EMS). According to the design, t...Show MoreMetadata
Abstract:
This paper presents the architectural lay-out and functional design details of a microcontroller embedded electronic monitoring system (e-EMS). According to the design, this unit is integrated into the PV module junction box. It can be scaled up to form part of a complex PV power plant control system. The communication topology follows a 3-tier structure. It uses two processors, one dedicated for data acquisition and the other for communication purposes. The e-EMS provides a complete set of data associated to PV module performance characteristic parameters, including current and voltage of the PV module and each sub-string of cells, operation of the bypass diodes along with the corresponding current and voltage measurements, PV temperature and environmental parameters. The sampling rate can be programmed in a large range from 1 to 65s along with the number of samples used for averaging signal values. The power output is determined every hour, as a basic output of the system. Comparison of the determined values with the expected ones when normalized to the PV operating conditions provides reliable information on deviation trends, the degree of degradation that the PV module experiences, while the analysis of the sampled data may identify the cells or modules which experience degradation and disclose types of factors which affect their operation.
Published in: 2019 8th International Conference on Renewable Energy Research and Applications (ICRERA)
Date of Conference: 03-06 November 2019
Date Added to IEEE Xplore: 13 February 2020
ISBN Information:
ISSN Information:
References is not available for this document.
Select All
1.
Kontges M. “Review of failures of Photovoltaic Modules ”, External final report IEA_PVPS, Task 13, March 2014, ISBN 978-3-609042-16-9.
2.
Jordan D.C., Kurtz S.R. “Photovoltaic Degradation Rates: An Analytical Review ” NREL/JA-5200-51664, June 2012.
3.
Kaplani E. “Detection of Degradation Effects in Field-Aged c-Si Solar Cells through IR Thermography and Digital Image Processing ” International Journal of Photoenergy, Vol. 2012, Article ID 396792, p. 1–11. doi: 10.1155/2012/396792.
4.
Kaplani E. “PV cell and module degradation, detection and diagnostics ” Renewable Energy in the Service of Mankind Vol II: Selected Topics from the World Renewable Energy Congress WREC 2014. Sayigh, A. (ed.). Switzerland : Springer International Publishing, p. 393–402.
5.
Breitenstein O., Rakotoniaina J.P., Al Rifai M. H., Werner M., “Shunt types in crystalline silicon solar cells ” Progress in Photovoltaics, 2014.
6.
Breitenstein O., Bauer J., Altermatt P.P., Ramspeck K. “Influence of Defects on Solar Cell Characteristics ” Solid State Phenomena, Vol. 156-158 ( 2010 ), pp 1–10, Trans. Tech. Publications, Switzerland.
7.
Croizier J., Van Dyk E.E., Vorster F. “Identification and characterisation of performance limiting defects and cell mismatch in photovoltaic modules ” J. En. in Southern Africa 26 ( 3 )( 2015 )pp 19–26, DOI: 10.17159/2413-3051/2015/v26i3a2126.
8.
Van Dyk E., Meyer E. “Analysis of the effect of parasitic resistances on the performance of photovoltaic modules ”, Renew. Energy 29 ( 3 ) ( 2004 ), pp. 333–344.
9.
Acciani G., Vergura S. “Typical defects of PV Cells ” 2010 IEEE International Symposium on Industrial Electronics, 2010, Bari, Italy, DOI: 10.1109/ISIE.2010.5636901.
10.